حاسبة حجم المسبح حر الشكل

Select Imperial (feet) or Metric (metres) at the top of the calculator. Imperial mode shows US gallons as the primary result; Metric mode shows litres first.

Results appear instantly in gallons, litres, and cubic feet. The accuracy badge shows the active tier's precision range — use the volume to dose chemicals, estimate fill time, or size a heater and pump.

Pool builders quote freeform pool dimensions as the bounding rectangle — the actual water volume is always 15–45% less because curved edges leave unfilled corners.

Freeform pool volume is the total amount of water the pool holds when filled to the normal waterline. It is expressed in US gallons, litres, or cubic feet and serves as the single number you need for chemical dosing, fill-time estimates, heater sizing, and pump turnover calculations.

Because every freeform pool has a unique irregular outline — curves, coves, peninsulas, and no two identical shapes — volume cannot be calculated with a single exact geometry formula the way a rectangular or round pool can. Instead, freeform pool volume is estimated from a bounding rectangle reduced by a compactness factor, or calculated more precisely from a known surface area multiplied by average depth.

Rectangles, circles, ovals, and other regular shapes have exact area formulas — π × r² for a circle, L × W for a rectangle. A freeform pool does not match any standard geometric outline, so no single formula applies to all freeform shapes.

Pool builders typically quote a freeform pool's dimensions as the bounding rectangle — the smallest rectangle that completely encloses the pool. The actual water surface occupies only a portion of that rectangle. How much of the rectangle is filled depends on how compact or irregular the pool outline is.

The compactness factor is a practical way to bridge the gap. A factor of 0.75 means the pool's water surface fills roughly 75% of the bounding rectangle, with 25% lost to curved edges and unfilled corners. Selecting a factor that matches the pool's outline — from 0.85 for near-oval shapes down to 0.55 for very irregular shapes — narrows the estimate.

If you have the pool's actual water surface area, the bounding-box estimate is unnecessary. Multiply surface area by average depth directly for a result accurate to ±2–5%. Sources of known surface area include:

The known-surface-area method bypasses all compactness guesswork and is the recommended path whenever the data is available.

Freeform pools have no fixed geometric formula because every shape is different. The accepted industry method is the bounding-rectangle approach: multiply the pool's longest length by its widest width to get a bounding area, then reduce that area by a compactness factor representing the fraction actually filled with water. This same approach applies to lagoon pools and other irregular shapes like kidney pools.

The Tier 2 result is 1,059 gallons (4,010 L) lower than Tier 1 because a typical freeform pool fills about 75% of its bounding rectangle, slightly less than the π/4 oval approximation (78.5%). This pool holds enough water to require approximately 4.5 gallons (17 L) of liquid chlorine per initial treatment at the standard 2 ppm dose rate.

The calculator offers three tiers. Tier 1 uses π/4 ≈ 0.785 as a general oval approximation (±15–25% accuracy). Tier 2 lets you select a compactness factor — Very Compact (0.85), Typical Freeform (0.75), Complex Freeform (0.65), or Very Irregular (0.55) — narrowing accuracy to ±10–15%. Tier 3 bypasses the bounding-box method entirely by accepting a known surface area from builder plans or a satellite measurement, achieving ±2–5% accuracy.

Always enter all dimensions in the same unit system. Mixing feet for length with metres for depth produces a wrong result.

A 40 × 20 ft freeform pool with a shallow end of 3.5 ft and deep end of 6.5 ft.

The Tier 2 result is 1,059 gallons (4,010 L) lower than Tier 1 because a typical freeform pool fills about 75% of its bounding rectangle, slightly less than the π/4 oval approximation (78.5%). This pool holds enough water to require approximately 4.5 gallons (17 L) of liquid chlorine per initial treatment at the standard 2 ppm dose rate.

Longest Length (L) is the full straight-line distance from one extreme end of the freeform pool to the other — tip to tip. Stretch the tape across the water surface in a straight line. The most common freeform measurement error is following the curved pool edge, which inflates the length by 10–20% and overestimates volume significantly.

Widest Width (W) is measured perpendicular to the length line at the pool's broadest point. This forms the second dimension of the bounding rectangle. On a freeform pool with an uneven outline, the widest point may not be at the centre — walk the tape along the length until you find the maximum perpendicular span.

Builder plans typically show the bounding rectangle as the overall pool dimension. The pool water surface is always smaller than this rectangle because of curves, coves, and irregular edges. A typical freeform pool occupies about 75% of the bounding rectangle area.

Average Depth = (Shallow End + Deep End) ÷ 2. Example: (3.5 + 6.5) ÷ 2 = 5.0 ft. Measure depth from the waterline straight down to the freeform pool floor — not along a sloped bottom or a curved wall.

Freeform pools almost always have variable depth with a gradual slope from shallow to deep. The two-point average approximates total water volume within ±3% for gradual slopes. For a freeform pool with an unusual floor profile — such as a flat shelf dropping sharply to a deep section — measure at 3 or 4 points along the length and average all readings for a tighter estimate.

The table below shows freeform pool volume at 8 standard bounding-rectangle sizes. All rows use 5.0 ft average depth (shallow 3.5 ft + deep 6.5 ft) and the Typical Freeform shape factor of 0.75.

Calculated using Volume (ft³) = L × W × Average Depth × Shape Factor. Shape factor 0.75 = typical freeform pool (approximately 75% of the bounding rectangle). 1 cu ft = 7.48052 US gal = 28.3168 L. Average depth = 5.0 ft (shallow 3.5 ft + deep 6.5 ft) ÷ 2. Use the calculator to enter your own shape factor for greater accuracy.

Most residential freeform pools fall between 25×15 ft and 50×25 ft (bounding rectangle), holding 10,000–35,000 gallons (38,000–133,000 L). A pool at the smaller end requires noticeably less chemical product per treatment — check the pool volume by size reference for comparisons across all shapes. Use the calculator above to enter your own depth and compactness factor for a result matched to your specific freeform pool.

Accuracy is the defining challenge of freeform pool volume estimation. A standard geometric formula works for rectangles and ovals because the math is exact. Freeform pools have no standard geometry — every pool has a different outline, different curves, and different proportions of filled versus unfilled space within the bounding rectangle.

Tier 1 (Quick Estimate) uses π/4 ≈ 0.785 as a general oval factor and produces results accurate to ±15–25%. This assumes the freeform shape is roughly elliptical, which works as a starting point but can over- or under-estimate by thousands of gallons on pools with deep coves or narrow peninsulas.

Tier 2 (Shape Compactness) narrows accuracy to ±10–15% by letting you select a factor that matches how compact or irregular the pool shape is. Very Compact (0.85) fits near-oval freeform pools. Typical Freeform (0.75) covers most residential pools. Complex Freeform (0.65) and Very Irregular (0.55) suit pools with many cutouts, coves, or narrow channels.

Tier 3 (Known Surface Area) achieves ±2–5% accuracy by bypassing the bounding-box estimate entirely. Enter the pool's exact water surface area from builder plans, a CAD drawing, or a satellite measurement tool such as Google Earth area measurement. The calculator then multiplies surface area by average depth — the remaining ±2–5% uncertainty comes only from depth measurement precision.

For chemical dosing, volume accuracy matters directly. A ±10% error on a 22,000-gallon (83,300 L) freeform pool means dosing for 19,800 or 24,200 gallons — a 4,400-gallon spread (16,656 L). At a standard chlorine dose of 2 ppm, that error translates to approximately 0.7 oz of liquid chlorine over or under the target. Over a full season of weekly treatments, the cumulative error adds up.

If your freeform pool builder provided a surface-area measurement at construction, use Tier 3 for all chemical and equipment calculations. If not, Tier 2 with the 0.75 factor provides a workable estimate for most residential freeform pools.

Chemical dosing. Chlorine, pH adjusters, and algaecides are dosed per gallon or per litre. A 15% volume error on a 22,000-gallon (83,300 L) freeform pool means adding chemicals for 18,700 or 25,300 gallons — enough to leave the pool under-sanitised or cause skin and eye irritation from over-treatment.

Fill-time planning. A standard garden hose delivers roughly 500 gallons (1,900 L) per hour. A 3,000-gallon volume error shifts the expected fill time by about 6 hours — the difference between finishing before dark and running the hose overnight.

Heater sizing. Pool heaters are rated by BTU output per hour. A heater sized for 18,000 gallons will take noticeably longer to raise the temperature of a pool that actually holds 22,000 gallons, adding hours to each heat cycle and increasing energy costs.

Pump and turnover rate. Pool pumps should circulate the full volume at least once every 8–12 hours. If the volume is underestimated by 20%, the pump may not complete a full turnover within the target window, reducing filtration and water clarity.

Avoiding over- or under-treatment. Under-dosing leads to algae growth, cloudy water, and higher corrective chemical costs later. Over-dosing wastes product and can damage pool surfaces. An accurate volume figure prevents both problems from the start.

1. Following the curved edge instead of measuring a straight line. The most frequent freeform pool measurement error. The tape should stretch in a straight line from one extreme end to the other — tip to tip — not follow the pool's curved perimeter. Following the edge inflates the length by 10–20% and overestimates volume by thousands of gallons.

2. Measuring the wrong width. Width must be the broadest perpendicular span across the pool, not the narrowest neck or a convenient measurement at the middle. Walk the tape along the length until you find the maximum perpendicular distance.

3. Using "typical 0.75" for every freeform pool. A near-oval pool fills about 85% of its bounding rectangle, while a pool with deep coves and peninsulas may fill only 55–65%. Picking 0.75 by default can over- or under-estimate volume by 10–15% if the shape does not match a typical freeform outline.

4. Mixing feet and metres. Entering length in feet and depth in metres — or vice versa — produces a result that is off by a factor of roughly 3×. Select one unit system in the calculator and use it for every input.

5. Using wall height instead of actual water depth. Pool walls extend above the waterline. Measure depth from the waterline down to the pool floor, not from the top of the coping or wall cap. Wall height overstates depth by 4–8 inches (10–20 cm) on most freeform pools.

6. Assuming quoted builder dimensions equal the true water surface area. Builder plans show the bounding rectangle. The water surface is always smaller because the freeform outline curves inward at the corners. Use the known surface area input (Tier 3) if the plans include an actual area measurement.